To get maximum satisfaction in car audio, you definitely need an amplifier, also if youplan to install you must install a subwoofer amplifier. Install the amplifier is not as hard as you think, can save more money than having to install it in stores by myself and a betterpair, here how to install the amplifier.
The first step
Decide where you will install the amplifier, if only you put speakers amplifiers can be placed just under the front seat if you will install penumpang.tetapi subwofer sureamplyfier close subwofer.
The second step
Prepare the following cable to the amplifier mounting
Power cable (+) red color, size according to the specifications listed in the manualamplifier, usually stated in units of AWG (the smaller the AWG value the greater thediameter of the cable, sample sizes smaller than 8 AWG to 4 AWG wire size). To500watt RMS power capacity is usually recommended to use size 4 AWG power cable.For measuring length distance from the battery to the amplifier, keep cable lengths as efficient as possible, for easy and neat arrangement of cables.
-Do not forget to put "fuse" (fuse) on the power cable (+) red, the ideal distance for theinstallation of a fuse is usually around 45cm measured from the position of the battery(+), install a fuse with 60Ampere size, type of fuse for audio lots sold in the market.
Ground wires (-) white color as big as the size of the power cable (4 AWG) with a length of not more than 90cm
RCA cable, according to the channel in 2 channel amplifier ya klo buy 2, klo 4channelbuy 4, and so on ...
Remote signal cable that connects the head unit with a power amplifier, no need largesize, fairly small cable wrote, about 18 - 8 AWG
Speaker cables, subwoofer cables if you plan on installing it
Cable terminal fork model.
The third step
Prepare the following tools-screwdriver (+), screwdriver (-)
-solder and insulation
-cutting pliers or scissors
The fourth step
-remove the head unit cd player from the dashboard of your car and check the order ofthe cord-remove the speaker dri dudukanya for you are easier to install and later on cable tidy.
guide
-read the installation instructions carefully and in accordance with the right or look forother clues younger ntuk u understand
-attach the speakers who are able to receive receive power amplifier with good
-read the installation instructions carefully and in accordance with the right or look forother clues younger ntuk u understand
-attach the speakers who are able to receive receive power amplifier with good
nstallation
The first step
Unplug min (-) battery
Do this always when you are working on electrical system on your vehicle to avoid a short-circuit
Connect the red wire (+) of the battery, plug fuse (45cm after the battery), proceed withconnecting wires coming out of the fuse to the amplifier (+) 12Volt DC. To avoid thedistortion earned positive cable (+) is not close to RCA cable, or with the speaker cable.
Connect the ground wires on the bolts that attached dibodi, make sure the bolts aregood condition, not rusty, sandpaper the surface of the body until you see the iron plate, attach the ground wires and bolts.
Remove the head unit and plug the remote cable contained in the head unit to the amplifier, then plug the RCA jacks are also located at the back of the head unit, make sure the correct position (left speaker and right speaker).
Continue to install the speaker cable (use insulation paper and mark it for the (+) and (-),and attach the speaker wires on the terminal (+) amplifier and (-) amplifier using sekunand solder to be strong and neat.
When you install a subwoofer, subwoofer cable (+) and (-) and adjust them as well as in the amplifier.
Make sure the amplifier has been seated properly, it should be noted also the circulation of air around the amplifier, because the amplifier easy to heat, and need adequatespace, intended for long-lasting shelf life amplifier.
Replace the cable min (-) battery, set the volume on the head unit's low, then Rev step bystep, test the resulting sound on each speaker, before you straighten your job.
When sound is produced on each of the speakers sounded good, rapihkan your job andset the amplifier in accordance with sound character you want.
Unplug min (-) battery
Do this always when you are working on electrical system on your vehicle to avoid a short-circuit
Connect the red wire (+) of the battery, plug fuse (45cm after the battery), proceed withconnecting wires coming out of the fuse to the amplifier (+) 12Volt DC. To avoid thedistortion earned positive cable (+) is not close to RCA cable, or with the speaker cable.
Connect the ground wires on the bolts that attached dibodi, make sure the bolts aregood condition, not rusty, sandpaper the surface of the body until you see the iron plate, attach the ground wires and bolts.
Remove the head unit and plug the remote cable contained in the head unit to the amplifier, then plug the RCA jacks are also located at the back of the head unit, make sure the correct position (left speaker and right speaker).
Continue to install the speaker cable (use insulation paper and mark it for the (+) and (-),and attach the speaker wires on the terminal (+) amplifier and (-) amplifier using sekunand solder to be strong and neat.
When you install a subwoofer, subwoofer cable (+) and (-) and adjust them as well as in the amplifier.
Make sure the amplifier has been seated properly, it should be noted also the circulation of air around the amplifier, because the amplifier easy to heat, and need adequatespace, intended for long-lasting shelf life amplifier.
Replace the cable min (-) battery, set the volume on the head unit's low, then Rev step bystep, test the resulting sound on each speaker, before you straighten your job.
When sound is produced on each of the speakers sounded good, rapihkan your job andset the amplifier in accordance with sound character you want.
Tidak ada komentar:
Posting Komentar